PermitsHubPermitsHub

ADUs

Can You Use Wireless Interconnected Smoke Alarms in a Legal Second Unit?

Wireless interconnected smoke alarms can save you from opening a finished ceiling. Whether an inspector will accept them depends on which code your second unit falls under. Here is how the Building Code path for a new unit differs from the Fire Code retrofit path for an existing two-unit house, and where the CO alarm has to go when both units share a furnace room.

By PermitsHub Team9 min read

Key Takeaways

  • A newly permitted second unit is inspected under the Ontario Building Code, which expects smoke alarms powered from a permanent electrical circuit with battery backup and interconnected so an alarm in one unit sounds in the other.
  • Battery-only wireless alarms will not satisfy the Building Code in a new unit, and hardwired alarms that use a listed wireless interconnect are accepted or refused depending on the code edition, the device listing and the inspector, so confirm before you buy.
  • An existing two-unit house being brought into compliance under the Ontario Fire Code retrofit rules usually has more flexibility on interconnection, which is often what decides whether a finished ceiling gets opened.
  • A fuel-burning furnace or water heater in a shared service room typically triggers a CO alarm in that room plus CO alarms near the sleeping areas in both units.

Wireless Alarms, Two Codes

For a brand new second unit built under a building permit, plan on hardwired smoke alarms: powered from a permanent electrical circuit, with battery backup, and interconnected so an alarm in one unit sounds in both units and any shared areas. Whether that interconnection can be wireless depends on the code edition your permit falls under, how the devices are listed, and the inspector assigned to your file. Battery-only wireless alarms won't pass in a new unit. For an existing two-unit house being brought up to the Ontario Fire Code retrofit standard, wireless interconnection is accepted far more often, and that difference is usually what decides whether a finished ceiling gets opened.

Two codes, two different answers about the same alarm

Most of the confusion online comes from people mixing up two separate rulebooks. The Ontario Building Code governs construction. If you're creating a second unit, finishing a basement into a suite, or converting a house to two units, you need a building permit, and a municipal building inspector checks your work against the Building Code before you get final sign-off.

The Ontario Fire Code governs buildings that already exist. It has a retrofit section written for two-unit houses, meant to bring older second units, many of them rented for decades, up to a reasonable level of life safety without rebuilding them. The local fire department enforces it, usually through a fire prevention inspector, and its requirements are written with finished, occupied homes in mind.

So a homeowner reads a fire department page saying wireless interconnected alarms are fine, buys a box of them, and then hears from the building inspector that the new suite needs hardwired interconnection. Neither office is wrong. They're applying different codes to different situations.

The question isn't whether wireless alarms are legal in Ontario. It's which code your unit is being judged under, and that's decided the day you apply for a permit.

What the building inspector expects in a newly permitted unit

Under the Building Code, smoke alarms are required on every storey of each dwelling unit, including the basement, inside every sleeping room, and in the hallway or area between the bedrooms and the rest of the storey. They have to be permanently connected to an electrical circuit with no disconnect switch between the alarm and the panel, and they need a battery as a backup power source. In a house with two units, alarms are interconnected so that one sounding anywhere sets off the alarms in both units and in common spaces like a shared laundry room or stair.

The part people want to bend is how the interconnect signal travels. Traditionally that's a third conductor in the alarm cable, run from alarm to alarm and across the fire separation between units. Newer national code editions recognize wireless interconnection for devices listed for that use, and Ontario's code has been moving closer to the national model. Acceptance in the field still isn't uniform. Some examiners accept hardwired-powered alarms that talk to each other wirelessly, provided the devices carry the right listing and the manufacturer's installation instructions are followed. Others want to see the physical interconnect conductor, especially when the walls and ceilings are open anyway.

If your permit covers a full basement finish, the ceiling is open at framing stage. Running interconnect wire costs little at that point, and arguing for wireless rarely makes sense. The wireless question really matters when part of the house is finished and staying finished, such as the upstairs unit in a conversion where only the basement is being renovated.

Why battery-only wireless alarms fail a permit inspection

The plug-in-nothing, battery-powered wireless alarms sold at hardware stores interconnect fine, but they fail the requirement for permanent connection to an electrical circuit. That requirement applies to every alarm the Building Code calls for in the new work, not just one per floor. We see these on final inspections more than you'd expect, usually installed by a contractor who did the same thing in a Fire Code retrofit job last month and assumed the rules carried over.

The Fire Code retrofit path for an existing two-unit house

Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.

The Fire Code retrofit section applies to houses that already contain two units, typically ones that existed before the current second-unit permit framework. Its goal is practical: working smoke alarms in each unit and in shared areas, alarms that warn the other unit, a reasonable fire separation, and safe ways out. It allows trade-offs. Interconnection between units can often be achieved by means other than running new wire through finished plaster, and fire prevention offices generally accept listed wireless interconnected alarms in this setting. Confirm the specifics with your local fire department, because the exact options depend on the house and the alternative measures in place.

This is the scenario where wireless saves real money and disruption. Picture a 1950s bungalow in Scarborough or Etobicoke with a basement apartment that's been rented for twenty years. The fire inspector arrives after a complaint or a tenant change and writes up deficiencies. Opening the lath-and-plaster ceilings upstairs to fish an interconnect wire is messy, slow and means patching, sanding and repainting. A listed wireless solution is often an accepted fix.

The catch: the moment you apply for a building permit to legalize or substantially renovate that unit, the work covered by the permit is judged under the Building Code. Homeowners sometimes assume an old unit's Fire Code compliance will carry forward. It covers what's existing and untouched, not the new work.

Where wireless interconnection works and where it gets you a fail

Across the GTA, from Toronto Building's districts to Vaughan, Markham and Mississauga, here's the pattern we see on second-unit inspections.

  • Usually accepted: hardwired alarms with battery backup in the new unit, physically interconnected, tied into existing upstairs alarms that are also hardwired and interconnected.
  • Often accepted with the right documentation: hardwired alarms in both units that use a manufacturer's listed wireless interconnect module, with the product listing and installation instructions available on site.
  • Accepted in Fire Code retrofits, not in permitted new work: battery-only wireless interconnected alarms.
  • Commonly flagged: mixing brands whose wireless protocols don't talk to each other, so pressing test in the basement doesn't sound the alarm upstairs.
  • Commonly flagged: a new hardwired suite circuit with the upstairs unit still on standalone battery alarms that don't communicate with the basement at all.

The test is simple and inspectors do it every time: press the test button on an alarm in one unit and walk to the other. If the other unit's alarms don't sound, it's a fail regardless of how the signal is supposed to travel. Wireless systems that need pairing should be paired and tested before the inspector arrives, not during the visit.

Remember the electrical side too. New hardwired alarm circuits are electrical work, so they fall under an Electrical Safety Authority permit pulled by a licensed electrical contractor. A building inspector will sometimes ask whether the ESA inspection has been done before closing out the alarm portion.

The CO alarm rule for a shared furnace room

Most GTA houses converted to two units keep a single gas furnace and water heater, usually in a basement mechanical room that both units depend on. That room is where carbon monoxide requirements get specific and where we see inspection comments repeat.

Under the Building Code, when a fuel-burning appliance sits in a service room shared by the units rather than inside one of them, CO alarms are generally required in the service room itself and adjacent to the sleeping areas in each dwelling unit. A fuel-burning appliance inside one unit, such as a gas fireplace in the upstairs living room, triggers CO alarms near that unit's sleeping areas. An attached garage counts as a CO source too. The Fire Code's CO requirements, brought in after the Hawkins Gignac Act, apply to existing homes and follow a similar logic: CO alarms near sleeping areas, plus the service room in buildings with more than one unit. Check the exact placement against current code text or with your inspector, since the wording has been updated over the years.

Mistakes we see in shared mechanical rooms

  • No CO alarm inside the furnace room because the owner assumed the ones outside the bedrooms covered it.
  • A CO alarm placed only in the basement unit, leaving upstairs bedrooms unprotected even though the furnace serves both units.
  • A plug-in CO alarm in a room with no receptacle except the one the furnace or sump pump uses, which ends up unplugged within a month.
  • A furnace room door left off its closer, or vented to the suite, which creates fire separation issues layered on top of the alarm issue.

Combination smoke and CO alarms are fine where both are required, and they reduce the number of devices on the ceiling. Just make sure the combination unit is hardwired and interconnected the same way your smoke alarms are, and that it carries the CO listing, not only the smoke listing.

Settle the alarm plan on the drawings, not at final inspection

Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.

The cheapest place to resolve the wireless question is on the permit drawings. A good second-unit set shows every smoke and CO alarm location on the floor plans for both units, notes that alarms are hardwired with battery backup and interconnected between units and common areas, and states the interconnection method. If you intend to use a listed wireless interconnect for an existing finished floor, say so on the drawings and identify the product. Then the plan examiner either accepts it or comments on it before anyone buys hardware or closes a ceiling.

When PermitsHub prepares second-unit drawings, the alarm layout and interconnection note go on the plans from the first submission, because a vague note like smoke alarms as per OBC invites an examiner comment or a surprise on site. If an examiner pushes back on wireless interconnection, we handle the revision and resubmission so you know the answer while the ceiling is still open.

Last practical point: talk to your electrician before framing inspection. If there's any doubt about acceptance, running a three-conductor cable to each alarm location while the walls are open costs little and keeps both options available. You can still use wireless upstairs where the plaster stays intact, and you won't be cutting drywall you just paid to hang.

Do I Need a Permit?

1
›
2
›
3
›
4

What are you planning to build or renovate?

ADU / Garden Suite Eligibility

What type of property do you have?

Ready to move forward? PermitsHub handles permit drawings, submission, and revisions - flat-rate, GTA-wide.

Related Reading

More in this category

ADUs

FAQ

Related questions

Get started

Tell us about your project.

Free, no-pressure quote within one business day.

● Flat-rate quotes - no surprise fees

● Revisions included until approval

● Most enquiries responded to same day

Free Home Permit QuoteNo commitment · 30 sec
1
2
3

What are you building?

SCROLL TO SEE ALL 20 PERMIT TYPES

Prefer to call? 647-961-4070
CALL NOWFree Home Permit Quote30 SECONDS - NO COMMITMENT