PermitsHubPermitsHub

Do I Need a Permit?

Do You Need an HRV After Air Sealing an Older Toronto House?

Air sealing and insulating an older Toronto house does not, on its own, force you to install an HRV. The code requirement usually comes from the permitted work around it, like an addition, a new heating system or a secondary suite. A tight old house with an atmospheric water heater can still backdraft carbon monoxide into your basement, so the code is only part of the decision.

By PermitsHub Team10 min read

Key Takeaways

  • Air sealing and insulation work by itself does not usually require a building permit or an HRV in Toronto, but the permitted work it is bundled with often brings the house under current Ontario Building Code ventilation rules.
  • Additions, new HVAC systems, secondary suites and major gut renovations are the common triggers that put mechanical ventilation on your drawings, and examiners will ask how the new space is ventilated.
  • The real danger in a tightened pre-war house is combustion spillage from naturally aspirated water heaters and older furnaces, so a depressurization or spillage test should happen before and after the sealing work.
  • An HRV is not the only compliant option, but in a tight house with a large range hood, gas appliances and finished basement, a balanced system is usually the safest and least troublesome choice.

Sealed Tight, Breathing Right

No, the Ontario Building Code does not generally require you to add an HRV just because you insulated and air sealed an older Toronto house. Sealing and insulation on their own usually don't need a building permit, so there's no code review that would demand new ventilation. The requirement shows up when the sealing is part of permitted work, such as an addition, a new heating system, a secondary suite or a gut renovation. In those cases the examiner will want mechanical ventilation shown on the drawings, and an HRV is often the simplest way to satisfy it. Separately from any code question, a tightened old house with gas appliances can become unsafe without balanced ventilation.

What the Building Code Actually Says About Existing Houses

The ventilation rules most people are thinking of live in Part 9 of the Ontario Building Code, in the section dealing with ventilation of houses. They set out what a mechanical ventilation system has to do: provide a principal exhaust or supply capacity, give occupants controls, and make sure combustion appliances aren't starved of air or pulled backwards by exhaust fans. Those rules are written for new construction and for the new portions of a renovated house.

Existing houses are handled through Part 11, the renovation part of the code. The basic idea of Part 11 is that you don't have to bring the whole house up to today's standard every time you touch it, but the work you do must not reduce the building's performance below what it was. Swapping drafty windows for new ones, blowing cellulose into the attic or spraying foam in the basement rim joist doesn't typically require a permit, which means nobody at Toronto Building is reviewing it against Part 9 ventilation at all.

That's the gap homeowners fall into. The work that most changes how a house breathes is often the work that never gets reviewed. Confirm the specifics of your own scope with Toronto Building, because what counts as a minor repair versus a renovation can depend on how much wall, ceiling or mechanical work is involved.

Renovation Work That Pulls You Into Current Ventilation Rules

In practice, the code ventilation requirement arrives through the side door. These are the scopes where we see examiners ask for mechanical ventilation details, or where the inspector will look for it at final:

  • Rear or second storey additions, where the new space has to meet current code and the energy efficiency requirements under Supplementary Standard SB-12, most of whose compliance paths assume heat recovery ventilation.
  • A new or substantially altered heating system, including new ductwork, where the HVAC design has to account for ventilation and the plans examiner may ask for heat loss calculations and a ventilation layout.
  • Secondary suites and basement apartments, where each dwelling unit needs its own ventilation approach and the separation between units affects how air can move.
  • Major interior gut renovations that open up most walls and ceilings, where the scope is large enough that the new work is reviewed as a renovation under the current code.
  • Multiplex conversions, including as-of-right fourplexes, where each unit's ventilation is reviewed and a single shared system rarely works.

If your air sealing is happening at the same time as any of these, assume ventilation will be on the permit drawings. Plan examiners will send back drawings that show an addition or suite with no ventilation design, and it's one of the more common revision comments we see on small residential files. Sorting it out before submission saves a round of revisions and a few weeks.

What happens if you skip the permit for the bigger work

We regularly see houses where the basement was finished, the attic was foamed and new windows went in, all without permits, and then the owner applies for an addition. The examiner and inspector see the house as it actually is. Unpermitted finished space can turn into an as-built permit problem, and the ventilation question comes along with it.

Why a Tightened 1920s House Starts Behaving Differently

Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.

Walk through a typical pre-war semi in Riverdale, the Annex or the Junction and you'll find double brick walls with no cavity insulation, plaster on lath, a stone or block foundation, original or early replacement windows and an attic with whatever someone blew in decades ago. These houses were never airtight. They got their fresh air through gaps at the rim joist, around window frames, at the attic hatch, through the chimney and up the old knob and tube penetrations.

That leakage was the ventilation system. It wasn't designed, but it worked well enough to clear moisture from cooking, showers and a family breathing in a small house. When you spray foam the rim joist, seal the attic floor and replace every window in one season, you can cut that leakage dramatically. The house doesn't know you meant well. Moisture that used to leak out now stays in.

The symptoms show up in the first winter: condensation running down the inside of the new windows, a musty smell in the basement, bathroom ceilings with mildew spots, and frost on the underside of the roof sheathing if the attic sealing was uneven. In double brick houses there's another risk. Adding interior insulation changes how the masonry dries, and trapped interior moisture getting into cold brick can contribute to freeze thaw damage. That's a separate design question, but it makes good ventilation even more important.

Every old house has a ventilation system. Air sealing doesn't remove the need for one, it just removes the one you had and leaves you with nothing unless you install a replacement.

The Backdrafting Risk That Rarely Comes Up at the Quote Stage

Moisture is the nuisance. Combustion spillage is the hazard. A lot of older Toronto houses still have a naturally aspirated gas water heater venting into the original masonry chimney, and some have an older mid efficiency furnace venting the same way. These appliances rely on a natural draft: hot flue gas rises up the chimney because the house isn't pulling against it.

Tighten the house, then run a big kitchen range hood, a clothes dryer and two bathroom fans at the same time, and the house goes into negative pressure. Air has to come from somewhere. In a sealed house the easiest path can be down the chimney, which pushes flue gases, including carbon monoxide, back into the basement. You won't see it, and in many cases you won't smell it.

The orphaned water heater problem

Here's one we see often in older Toronto houses. The owner upgrades to a high efficiency furnace that vents out the side wall through plastic pipe. The old water heater is now alone in a large masonry chimney that was sized for a furnace and water heater together. A small appliance in a big cold flue struggles to establish draft, and condensation can damage the chimney liner. Add air sealing on top of that and spillage becomes much more likely. Gas appliance venting falls under the gas code and is the territory of a licensed gas technician, who may require a liner or a different water heater altogether.

The practical fix is testing. A qualified contractor or energy advisor can do a depressurization or spillage test with the house in a worst case condition: exhaust fans on, dryer running, interior doors positioned to make things worse. Doing this before and after the sealing tells you whether you've created a problem. Every house with gas appliances should have working carbon monoxide alarms regardless, and Ontario law requires them in homes with fuel burning appliances or attached garages.

Range hoods and makeup air

Renovated kitchens in older houses often get a powerful range hood because the owners cook a lot or the designer specified one. In a leaky house a large hood just pulls through the gaps. In a sealed house it can overpower the chimney. The code addresses exhaust equipment and its effect on combustion appliances, and for larger hoods you may need dedicated makeup air. This is a detail that examiners and HVAC designers do pick up on, especially in kitchen and addition permits.

HRV, ERV or Exhaust Only: Choosing the Right Approach

The code doesn't say you must have an HRV. It sets performance requirements, and there's more than one way to meet them. What makes sense depends on how tight the house ends up and what's burning fuel inside it.

  • An HRV (heat recovery ventilator) brings in fresh outdoor air and exhausts stale indoor air in balanced amounts, transferring heat between the two streams. Because it's balanced, it doesn't push the house negative, which is why it's the safest pairing with atmospheric appliances.
  • An ERV (energy recovery ventilator) works the same way but also transfers some moisture. Some designers prefer it for very tight houses where winter air gets uncomfortably dry, though in older houses with existing moisture issues an HRV is usually the more common choice.
  • Exhaust only systems use a continuously rated bathroom fan or central exhaust to remove stale air, with replacement air coming in passively. They're cheaper to install but they depressurize the house, which is exactly what you don't want next to a naturally aspirated water heater.
  • Supply ventilation tied to the furnace brings fresh air into the return ductwork. It can work in some houses but it's harder to balance and needs careful design.

Installing an HRV in an older house is mostly a ductwork question. Where does it physically go, usually in the basement mechanical room? Can it connect to the furnace ducts, or does it need its own runs to bathrooms and kitchen? Can you get the intake and exhaust hoods through the wall at the right distances from the gas meter, the dryer vent and the neighbour's window, which on a narrow Toronto lot with a shared side yard is often the hardest part? The cost drivers are the duct work and the wall penetrations far more than the unit itself, and a dedicated duct system costs meaningfully more than tying into existing furnace ducts.

How to Sequence the Work So It Holds Up at Inspection

Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.

The houses that go smoothly are the ones where ventilation is designed before the sealing starts, not added after the first winter of wet windows. A sensible order looks like this:

  • Get a baseline blower door test and combustion safety check, so you know how leaky the house is and whether any appliance is already marginal.
  • Decide whether the sealing is part of a larger permitted project. If it is, put the ventilation design on the permit drawings from the start.
  • Deal with atmospheric appliances first. Replacing a naturally aspirated water heater with a sealed combustion or power vented unit removes most of the backdrafting risk.
  • Do the air sealing and insulation, paying attention to how the brick walls and attic will dry.
  • Install and balance the ventilation system, then run a final test to confirm the house isn't going negative under worst case conditions.

On permitted jobs, the HVAC inspection will look at the ventilation installation, the duct connections and the exterior terminations. Inspectors flag intake hoods too close to exhaust sources and units that were installed but never balanced. Keep the commissioning report from your HVAC contractor, because a balanced airflow record makes the final much simpler.

We've done a lot of this work on pre-war semis and detached houses in east end and midtown Toronto, where the same combination keeps coming up: double brick, a chimney with an orphaned water heater and an owner who just foamed the basement. When the project needs a permit, PermitsHub prepares the drawings with the ventilation and HVAC information the examiner expects, so the file doesn't come back asking how the new space breathes. If you're unsure whether your scope crosses the permit line, a zoning and code review before you start is cheaper than finding out from an inspector.

Do I Need a Permit?

1
›
2
›
3
›
4

What are you planning to build or renovate?

Ready to move forward? PermitsHub handles permit drawings, submission, and revisions - flat-rate, GTA-wide.

Related Reading

More in this category

Do I Need a Permit?

FAQ

Related questions

Get started

Tell us about your project.

Free, no-pressure quote within one business day.

● Flat-rate quotes - no surprise fees

● Revisions included until approval

● Most enquiries responded to same day

Free Home Permit QuoteNo commitment · 30 sec
1
2
3

What are you building?

SCROLL TO SEE ALL 20 PERMIT TYPES

Prefer to call? 647-961-4070
CALL NOWFree Home Permit Quote30 SECONDS - NO COMMITMENT