Basements
Does a Basement Bedroom Need an Egress Window If It Is Not a Rental?
Plenty of homeowners assume egress windows are a landlord problem. They aren't. Under the Ontario Building Code, any new bedroom in an unsprinklered home needs a window someone can climb out of, rental or not. Here are the exact numbers inspectors check, and why a slider that looks big enough often isn't.
Key Takeaways
- The Ontario Building Code requires an egress window or exterior door in every bedroom of an unsprinklered dwelling unit, so a basement bedroom in your own single-family home needs one even if it will never be rented.
- The window must give an unobstructed opening of at least 0.35 m² with no dimension under 380 mm, and it has to stay open on its own without anyone holding it.
- If the window opens into a well, you need at least 760 mm of clear space in front of it, and an outward-swinging sash cannot eat into that space.
- Sliders and hoppers often fail because only part of the frame actually opens, so you have to measure the clear opening, not the rough opening or the glass.
Basement Bedroom Egress Rules
Yes. If you're adding a bedroom to the finished basement of a single-family Ontario home and the house is not sprinklered, that bedroom needs an egress window (or an exterior door) whether you rent it or not. The Ontario Building Code requires a window that opens from the inside without keys or tools and gives an unobstructed opening of at least 0.35 m², with no single dimension smaller than 380 mm. If that window opens into a window well, there has to be at least 760 mm of clear space in front of it. Those are the numbers your plan examiner checks on the drawings and your inspector checks with a tape measure.
The Rule Follows the Bedroom, Not the Tenant
The confusion is understandable. Most of what homeowners read about egress windows comes from articles on legal basement apartments, so people file it under rental rules. But the bedroom egress requirement sits in Part 9 of the Ontario Building Code under the general provisions for dwelling units. It applies to any bedroom in a house that isn't sprinklered. Your teenager's room, the guest room, the nanny's room: same rule as a tenant's bedroom.
The logic is simple. A basement bedroom usually has one way out: up the stairs, often past the furnace room and right through the floor where a fire is most likely to spread. If that route fills with smoke at 3 a.m., the window is the second way out. The code doesn't care who's sleeping there or whether they pay rent.
Where rental status does matter is everything else. A secondary suite brings in fire separations, sound ratings, separate smoke alarm interconnection, and in Toronto, a separate rental licensing system. A basement bedroom in your own house skips most of that. The egress window is one of the few requirements that carries over unchanged.
Calling it an office doesn't get you out of it
We see this on drawings every few months: a room with a closet, a door, and a layout that is obviously a bedroom, labelled "office" or "den" or "flex room." Plan examiners look at the room, not the label. If it has a closet and it's sized like a bedroom, expect a comment asking you to show compliant egress or explain the use. Even when a relabelled room gets through permit, it comes back to bite you at resale, when a buyer's home inspector notes a basement sleeping room with no way out and the listing can't honestly call it a bedroom.
Plan examiners read floor plans the way buyers do. A room with a closet and a door is a bedroom, whatever word you print inside it.
The Three Measurements That Decide Pass or Fail
The clear opening: 0.35 m² and 380 mm
The opening is measured when the window is fully open, from the edges of whatever is left in the way: the frame, the sash, the operator arm, the hinge hardware. It is not the rough opening in the foundation and it is not the glass size on the window supplier's quote. Both conditions apply at the same time. An opening 380 mm wide by 921 mm tall just meets 0.35 m². So does 500 mm by 700 mm. An opening 350 mm by 1,200 mm has plenty of area but fails, because one dimension is under 380 mm. That narrow-but-tall shape is exactly what you get from a lot of standard basement casements with chunky frames.
The code also requires the window to hold that opening during an emergency without extra support. A sash you have to prop up with one hand while you climb out with the other doesn't count. That one line is what sinks most awning-style basement windows.
Sill height: what the code says and what inspectors actually look at
People search for an exact maximum sill height and are surprised to learn the Ontario Building Code's bedroom egress provision doesn't set one. Some other provinces and building codes do, which is where most of the numbers floating around online come from. In Ontario, the test is practical: can a person actually get up to the window and out of it? A sill at chest height above a bare drywall wall in a dark room is a real problem, and some examiners and inspectors will raise it. The common fixes are lowering the window in the foundation when you're cutting a new opening anyway, or building a fixed step or bench below it. If your sill is high, confirm with your municipality's building department before you frame, because local practice varies more on this point than on the opening size.
The window well: 760 mm clear in front
When the window opens into a well, you need at least 760 mm of clear space measured out from the face of the window to the inside of the well. That space is for a body, not a cat. A person has to drop into the well, turn and climb out. The code adds that if the sash swings toward the well, its operation can't reduce that clearance in a way that blocks escape. In practice, an outswing casement or awning that hits the well wall halfway open is a fail, even if the well itself measures 760 mm deep.
The code is less prescriptive about the rest of the well, but inspectors look at the whole escape path. A deep well with smooth corrugated steel walls and no steps is hard to climb out of, and most well manufacturers sell units with built-in ladder rungs for that reason. Any cover over the well has to be openable from below without tools or special knowledge. A bolted-down polycarbonate dome over an egress well will be written up.
How Casement, Slider and Hopper Windows Measure Against 0.35 m²
Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.
Window style changes the clear opening more than anything else. Two windows with identical frame sizes can give completely different results.
- Casement: hinged on the side, swings fully open, and gives you close to the full sash opening, so it is usually the easiest way to hit 0.35 m² in a small frame. Watch for operator arms and standard hinges that stop the sash short of 90 degrees and leave it sitting in the opening. Egress hinges, which let the sash swing clear, solve that. If it swings outward into a well, check the 760 mm clearance with the sash open.
- Slider: only one sash moves, so you lose roughly half the frame width plus the meeting rail. A slider with a frame about 1,200 mm wide and 600 mm tall can easily end up with a clear opening around 540 mm by 500 mm, roughly 0.27 m², which fails even though the window looks generous from the room. Sliders work for egress, but they need a wider or taller frame than people expect.
- Hopper: hinged at the bottom and tilting in from the top. The tilted sash sits right in the escape path and most hoppers only open partway, so they rarely pass unless the sash can swing fully clear without removing hardware. The code specifically excludes windows that only work if you take out the sash.
- Awning: hinged at the top and swinging out. It has to stay open without being held, and it swings straight toward the well. It's one of the hardest styles to make work below grade.
The fix for a borderline window is always the same: get the manufacturer's clear opening dimensions in writing before you order, and put them on your drawings. Examiners increasingly ask for the egress window size as a clear opening, not a frame size, and a window spec sheet answers that comment before it is issued.
When the Existing Basement Window Won't Pass
Across North York, Scarborough and Etobicoke, the typical 1950s and 1960s bungalow came with small hopper or slider windows set high in the foundation wall, often around 300 to 400 mm tall. None of those pass as bedroom egress. In our work on basement renovations in those neighbourhoods, the existing window is almost never usable as-is, and the real question is how much foundation has to come out.
Enlarging an opening in a foundation wall is structural work. You are removing part of a wall that carries the floor and the walls above, so the new opening needs a properly sized lintel, and poured concrete and block foundations each have their own detailing. That has to be shown on permit drawings. Below grade, it also means excavating outside for the new well, dealing with the drain tile, a drain at the bottom of the well, and whatever is in the way: a gas meter, an AC unit, a side-yard walkway, the neighbour's fence on a tight lot. That outside work is often the biggest cost driver of the whole bedroom, meaningfully more than the window itself.
Side-yard wells are where we see the most surprises. On narrow Toronto lots, a well that projects 760 mm or more from the wall can block the only walkway to the backyard or end up hard against the lot line. Pick the window location early, before the bedroom layout is locked in, so the well lands somewhere practical. When PermitsHub prepares basement drawings, we place the egress window and well on the site plan first and design the room around it, because moving a bedroom wall on paper is much easier than moving a foundation opening.
What Gets Flagged at Plan Review and Final Inspection
Most egress problems are predictable. These are the ones we see most often, roughly in order of how often they come up.
- Window sizes shown as rough opening or frame size on the drawings, with no clear opening dimension, which triggers an examiner comment and a resubmission.
- A window that meets 0.35 m² but has one dimension under 380 mm, usually a narrow casement.
- Window wells that were ordered to fit the window width but don't give 760 mm of projection.
- Outswing sashes that hit the well wall before they are fully open.
- Restrictor hardware or window locks that need a key, left in place by the installer.
- Well covers screwed down or too heavy to push open from inside.
- Furniture or built-in shelving designed directly in front of the window on the drawings, which inspectors sometimes question.
The inspector will open the window, measure it, and often look out at the well. Have the window installed, the hardware working and the well finished before you book the final. A half-backfilled well with no drain gets you a return visit.
Sprinklers, Doors and Bedrooms That Already Exist
Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.
There are a few real exceptions, and they get misread.
The window requirement doesn't apply where the dwelling unit is sprinklered. That doesn't mean putting a sprinkler head in the basement bedroom. It means a properly designed and installed residential sprinkler system for the unit, which is a significant project of its own and rarely makes sense in an existing house just to avoid one window.
An exterior door from the bedroom also satisfies the requirement. In walkout basements, a bedroom with its own door to the backyard is often the cleanest answer and skips the window well question entirely.
Existing basement bedrooms that were finished years ago, before the current rules or without a permit, are a grey area. The code generally applies to new construction and alterations, so an untouched room isn't automatically ordered to change. But once you apply for a permit to renovate that space, or the work comes to the municipality's attention, the bedroom will be reviewed against current requirements. If you're unsure whether your existing room counts as new work, confirm with your local building department before you start, or get a review of your plans first.
The safest assumption for anyone finishing a basement in Toronto, Mississauga, Vaughan, Markham or anywhere else in the GTA: if someone will sleep in that room, plan for a 0.35 m² clear opening, no dimension under 380 mm, and 760 mm of well clearance from day one. It is far cheaper to design around those numbers than to discover them at final inspection.
Do I Need a Permit?
What are you planning to build or renovate?
Ready to move forward? PermitsHub handles permit drawings, submission, and revisions - flat-rate, GTA-wide.