PermitsHubPermitsHub

Basements

Fire-Rated Door and Stair Enclosure Between a Basement Unit and Upstairs

Most basement suite advice stops at the ceiling. The door and stairwell connecting the two units fail inspection far more often in older GTA houses, usually over missing closers, hollow doors, open stair soffits and a stray return air grille. Here is what the Ontario Building Code expects at that connection, and where existing houses get some room to move.

By PermitsHub Team9 min read

Key Takeaways

  • Any door between a basement unit and the upper unit has to sit in the fire separation, which normally means a 45 mm solid core wood door or a labelled 20-minute door, in a solid frame, with a self-closer that latches the door on its own.
  • An open basement stair has to be fully enclosed on the side facing the other unit, including the underside of the stringers, the walls and any closet under the stair, using the same rated drywall assembly as the ceiling.
  • Existing houses can often use the Part 11 compliance alternatives or the Fire Code retrofit rules for two-unit houses, which may accept a lower separation rating paired with interconnected smoke alarms, but the door closer is almost never waived.
  • Most re-inspections at the stairwell come from small penetrations like return air grilles, electrical boxes, foam-filled frame gaps and door swings over a step, all of which can be designed out on the permit drawings.

Doors, Closers, Stair Enclosures

Where a basement unit's stairway or door connects to the main house, the Ontario Building Code treats that connection as part of the fire separation between two dwelling units. In practice that means a solid core wood door at least 45 mm thick (or a labelled 20-minute fire-rated door) in a proper frame, a self-closing device that pulls the door shut and latches it, and a stair enclosure finished in fire-rated drywall on every side facing the other unit, including the underside of the stair. Existing houses can sometimes use relaxed compliance alternatives for the wall and ceiling rating, but the closing, latching door is the part inspectors almost never let slide.

Which Rulebook Your House Falls Under

Before anyone specifies a door, you need to know which set of rules applies, because the answer changes what's acceptable. There are three paths we see in the GTA.

  • New construction or a full gut where the house is treated as new: Part 9 of the Ontario Building Code applies directly, and the separation between units is typically a 30-minute assembly with doors that meet the Part 9 door rules.
  • Renovating an existing house to add a second unit: the designer can usually use Part 11 of the Code, which includes compliance alternatives for existing buildings. These often allow a lower separation rating where smoke alarms are interconnected between both units.
  • An older two-unit house being brought into compliance after a fire department inspection: the Ontario Fire Code has a retrofit section for two-unit residential occupancies, enforced by the local fire service, with its own list of acceptable door and separation options.

Toronto Building, Vaughan, Markham, Mississauga and the other municipalities all apply the same provincial Code, but individual examiners differ on how much detail they want to see before they'll accept a compliance alternative. The safe approach is to show the exact door, frame, closer and drywall assembly on the drawings and name the Code provision you're relying on. Confirm the specific rating your project needs with the municipality, or have your designer spell it out in the code matrix on the cover sheet.

What the Connecting Door Actually Has to Be

The door between units is the weak point of the whole separation, so the Code is specific about it. A hollow core interior slab, which is what most original basement doors in post-war houses are, does not qualify. Neither does a decorative six-panel door that looks heavy but is hollow inside. Knock on it. If it sounds like a drum, it's coming out.

Acceptable door options

  • A solid core wood door not less than 45 mm thick, which the Code accepts in place of a rated door in many residential separations.
  • A door with a 20-minute fire protection rating, which will carry a label on the hinge edge from the manufacturer. Leave the label on and don't paint over it.
  • A steel insulated door, which is common where the connecting door also serves as an exterior or vestibule door.

The frame matters as much as the slab. The door needs a solid frame properly fastened to the stud framing, with the gap between frame and rough opening filled with a material that won't burn away, usually fire-rated sealant or strips of drywall. Spray foam alone in that gap is a common deficiency. Glass lites, pet doors and mail slots in this door are generally not permitted unless the door is rated as a complete assembly with them. We've seen buyers of converted houses lose a re-inspection over a frosted glass panel a previous owner put in for light.

Self-Closers and Latching: The Hardware That Fails Most Often

Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.

A fire separation only works when the door is closed. That's why doors in a required fire separation need a self-closing device, and why inspectors test it by opening the door partway and letting go. If it doesn't close fully and latch on its own, it fails. It's as simple as that, and it's the single most common stairwell deficiency we see.

Inspectors don't look at the closer, they let go of the door. If it stops a few centimetres short of the latch, the rating on the slab is irrelevant.

Spring hinges are the most popular option because they're discreet, and they're generally accepted if they're installed and adjusted correctly. The usual failure is too few spring hinges for a heavy solid core slab, or hinges that weren't tensioned. A heavier door often needs all its hinges to be spring hinges, or a surface-mounted closer arm at the top. Surface closers are more reliable but tenants and owners sometimes dislike the look.

Other hardware problems that show up at final inspection:

  • A passage set with no latch, or a roller catch, which lets the door bounce open under air pressure from the furnace.
  • Kick-down door stops, magnetic holders or hooks that keep the door propped open. Hold-open devices aren't acceptable on these doors unless they're the approved type tied into the alarm system, which almost no house has.
  • A large undercut at the bottom of the door left from when it was used as a return air path. Keep the gap at the bottom small and consistent.
  • Weatherstripping or smoke seals that are so thick the closer can't overcome them, so the door hangs open a crack.

Smoke gaskets are not always mandatory in a residential separation, but a tight-fitting door with a minimal gap is. Some examiners and fire inspectors ask for perimeter seals on the connecting door, particularly under the Fire Code retrofit path, so specify them on the drawings if there's any doubt and adjust the closer accordingly.

Enclosing an Open Basement Stair

In the bungalows and storey-and-a-half houses we draw across Scarborough, Etobicoke and North York, the basement stair is usually open: unfinished stringers, a railing on one side and a bulkhead overhead. Turning that basement into a separate unit means deciding which unit the stair belongs to and then enclosing it so smoke from one unit can't travel up or down it into the other.

The side door landing layout

The most common GTA arrangement is a side entrance at grade with a short flight up to the kitchen and a longer flight down to the basement. The cleanest solution is often to make that landing a shared entry, with one door at the top into the upper unit and one door at the bottom into the basement unit. Both doors sit in the fire separation, and the landing walls and ceiling become part of the rated enclosure. If the landing is the basement tenant's only way out, it has to stay protected and usable even if there's a fire upstairs, which is why the door into the main house is the one examiners scrutinise hardest.

Watch the door swing. A door at the top of a stair that swings out over the first step is a problem, and so is a door that hits the handrail. Often the landing is too small for a door to swing in either direction without conflict, which forces a reconfigured landing, a relocated door or a change in which way the stair runs. That's a framing conversation you want during design, not after the drywall is up.

Walls, underside and the closet under the stair

The enclosure must be continuous. Any face of the stairwell that faces the other unit needs the same rated assembly as the ceiling, typically Type X drywall on the stairwell side with taped and filled joints. The detail people miss is the underside of the stair. If the basement unit's living space runs under the upper unit's stair, the soffit under the stringers needs rated drywall too, and so do the walls of any storage closet tucked under there. A closet with an unfinished ceiling under the stair is a direct path from the basement into the upper stairwell.

The separation also has to run tight to the rest of the assembly. The wall drywall should meet the rated basement ceiling without a gap, and where the stair wall meets the foundation wall or the floor above, the joints need to be sealed. If the rated ceiling stops at the stairwell opening and the stairwell walls aren't rated, the whole separation has a hole in it the size of the stair.

Small Penetrations That Undo a Rated Stairwell

Once the door and drywall are right, the remaining failures are almost always small openings that tradespeople didn't think of as part of the fire separation. The stair wall is a favourite place for a return air grille, a light switch, a thermostat or the electrical panel, because it's central. Each of those can compromise the enclosure.

  • Return air or supply grilles in the stairwell wall that connect the two units through shared ductwork. Separate HVAC systems or proper fire dampers usually have to be addressed on the drawings.
  • Electrical boxes cut into the rated face of the stair wall, especially back-to-back boxes on both sides of the same stud cavity.
  • Plumbing and gas lines passing through the stair enclosure without a fire stopping system around them.
  • Pot lights in the stair soffit or landing ceiling that aren't rated or boxed in.
  • The old laundry chute, which in some older houses drops right beside the stair.

Ductwork and lighting penetrations deserve their own planning, and they're covered in more detail in our piece on basement suite ceilings. For the stairwell, the short version is to keep the enclosure faces as blank as possible and move switches, grilles and thermostats to walls that aren't part of the separation.

Planning It So the Stairwell Passes the First Time

Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.

The examiners who review basement suite applications look for the connecting door and stair enclosure on the floor plans and in the sections. Drawings that say only "fire separation as per OBC" next to the stair tend to come back with a comment asking for the door type, closer, frame and wall assembly. A door schedule that names the slab, rating, closer and seals, plus a section through the stair showing the soffit drywall, avoids that round of revisions. At PermitsHub this is one of the details we draw out explicitly on basement suite permit sets, because it's where a vague drawing turns into a vague installation and then a failed inspection.

On site, sequence matters. The insulation and drywall inspection is your chance to have the inspector see the stair soffit, the closet under the stair and the frame gaps before they're closed in. Don't install the connecting door until the closer type is confirmed, and test it yourself with the furnace running, because air pressure from the system can hold a door open that closes fine when everything's off. If you're legalising an existing unit, expect the fire service or building inspector to start at this door, because it's the fastest indicator of whether the rest of the separation was taken seriously. We regularly coordinate those re-inspections for owners who inherited a converted house, and the door and stairwell are where the fixes usually begin.

Do I Need a Permit?

1
›
2
›
3
›
4

What are you planning to build or renovate?

Ready to move forward? PermitsHub handles permit drawings, submission, and revisions - flat-rate, GTA-wide.

Related Reading

More in this category

Basements

FAQ

Related questions

Get started

Tell us about your project.

Free, no-pressure quote within one business day.

● Flat-rate quotes - no surprise fees

● Revisions included until approval

● Most enquiries responded to same day

Free Home Permit QuoteNo commitment · 30 sec
1
2
3

What are you building?

SCROLL TO SEE ALL 20 PERMIT TYPES

Prefer to call? 647-961-4070
CALL NOWFree Home Permit Quote30 SECONDS - NO COMMITMENT