Structural
Tying a Rear Addition Roof Into Existing Trusses Without Overloading Them
You can tie a rear addition roof into an existing house, but you can't cut, notch or extend engineered roof trusses on your own judgment. Any change needs a revised design from the truss manufacturer or a professional engineer. And because a lower roof against a taller house collects drifting snow, the framing behind your addition often turns out much heavier than anyone expected.
Key Takeaways
- Engineered roof trusses in Ontario cannot be cut, notched, extended or loaded with new framing unless the truss manufacturer or a professional engineer provides a revised design or repair detail.
- A lower addition roof built against a taller house collects drifting and sliding snow, so the design load near the wall can sit well above the base snow load for your municipality.
- Drift loads commonly push the design toward girder trusses, multi-ply headers, engineered hangers and new point loads that must be carried continuously down to an adequate footing.
- Plan examiners most often return addition drawings because drift is not shown, the load path under a girder bearing stops at the floor, or existing trusses are being altered with no engineering behind it.
Trusses, Drift and Load
Yes, you can tie a rear addition roof into an existing house in Ontario, but you cannot cut, notch, extend or hang new framing off existing engineered roof trusses without a revised design from the truss manufacturer or a professional engineer. Snow drift is what usually changes the plan. A lower addition roof sitting against a taller house collects wind-blown and sliding snow, so the load near the wall can be far higher than the base snow load for the GTA. That extra load often means girder trusses, bigger headers and new point loads that have to travel all the way down to the foundation.
That's the short version. The longer version is where most addition projects either stay on schedule or lose weeks in plan review, so it's worth walking through how the roof actually meets the house and what the examiner expects to see on paper.
Why a Truss Is Not a Rafter You Can Trim
A conventionally framed roof uses rafters and ceiling joists, and a carpenter can sometimes head off or sister a rafter with fairly predictable results. A truss is different. It's a triangulated system where the top chord, bottom chord and every web are working together, some in tension and some in compression, joined by metal connector plates sized for one specific set of loads. Cut a single web to open up a ceiling or remove a bottom chord to make room for a vaulted transition, and the forces have nowhere to go.
The Ontario Building Code requires trusses to be designed by engineering methods, and the manufacturer's truss design drawings are prepared and sealed for those exact members and loads. Once the house is built, those drawings are the only record of what each truss can carry. Change the truss or add load to it, and you need either a repair or modification detail from the original manufacturer or a design from a professional engineer who takes responsibility for the altered system. Inspectors in Toronto, Vaughan and Mississauga will ask for that paper at the framing inspection if they see a modified truss, and they're right to.
The truss that fails is rarely the new one. It's the old truss that quietly picked up a valley, a snow drift and a cut web that nobody wrote down.
Three Ways an Addition Roof Can Meet the House
Before anyone sizes a single member, the roof geometry has to be decided, because each option loads the existing structure differently. This decision belongs at the concept stage, not after the drawings are half done.
A shed or flat roof that stops below the existing eaves
This is the most common option for single-storey rear additions on Toronto semis and North York bungalows. The new roof bears on a ledger fastened to the existing rear wall, or on its own beam and posts just in front of it, and it never touches the existing trusses at all. The catch is that the existing roof now sits directly above the new one, so snow sliding off the upper slope and drifting off the upper roof lands right where the addition meets the house. Clean on paper, heavy in February.
An overframed valley sitting on top of the existing roof
When the addition roof is pitched to match the house, framers often build the new roof right over the existing shingles, with valley framing or piggyback sections bearing on the old trusses. It looks seamless from the yard, but it adds dead load to trusses that were never designed for it, and it creates a valley where snow piles up. This is the option most likely to need a manufacturer's letter or an engineer's analysis of the existing trusses.
Removing part of the existing roof to continue the ridge
Sometimes the best design removes the rear gable end truss, or several trusses, so the new roof continues the existing ridge line. This is a true modification. The gable end truss is often a non-structural sheathed frame bearing on a full wall, and once that wall is opened for the addition, the trusses next to it see completely different support conditions. Expect a girder truss or engineered beam to pick up the cut members, and expect the engineer to want to see the existing truss design drawings.
How Snow Drift Changes the Load on the Lower Roof
Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.
The specified snow load for any roof in Ontario starts from the ground snow and rain load values for your municipality listed in Supplementary Standard SB-1. A plain, unobstructed roof gets a reduced share of that ground snow because wind scours some of it away. A lower roof next to a taller wall gets the opposite treatment. Wind carries snow off the upper roof and drops it in the sheltered zone against the wall, building a wedge that is deepest at the wall and tapers out over the lower roof.
Truss designers and engineers use the drift provisions in Part 4 of the Code to size that wedge. Two things drive it: the height difference between the two roofs, and how much upper roof area is feeding snow down. A single-storey addition against a two-storey house in Markham or Richmond Hill can see a drift load near the wall that is several times the load on the open part of the same roof. A steep upper roof that sheds snow onto the addition adds sliding load on top of the drift.
Here's the part homeowners rarely expect. If your addition is two storeys and your existing house is a bungalow or a storey-and-a-half, the existing roof becomes the lower roof. Now the drift lands on the old trusses, and those trusses were designed decades ago with no tall wall beside them. That situation almost always needs an engineer to check the existing roof, and sometimes it needs reinforcement or replacement of trusses near the new wall.
What the Extra Load Does to the Framing Below
Drift doesn't stay in the roof. It follows the load path down, and every element along that path has to be sized for it. On a typical rear addition the chain of consequences looks like this:
- Standard trusses near the house get replaced or supported by a multi-ply girder truss that collects the drift area and delivers it to two concentrated bearing points.
- Truss-to-girder connections move from toe nails to engineered hangers with specified fasteners, and the inspector will check that every nail hole is filled.
- The header over the widened opening in the existing rear wall has to carry roof load, drift and any floor above, which often pushes it from built-up lumber to LVL or steel.
- Each end of that header and each girder bearing becomes a point load that needs solid blocking or a built-up post through every floor down to the foundation.
- The footing under that post may need to be enlarged or a new pad footing poured, especially where the existing rear wall sits on a shallow or undersized footing.
The last two items are where budgets and schedules shift. Older Toronto houses in the Junction, Leslieville or the Danforth often have rear walls on rubble or shallow concrete footings, and a new concentrated load from a girder can be more than that footing was ever meant to carry. Postwar bungalows in Scarborough and Etobicoke usually have better footings, but the posts frequently land on a basement floor slab instead of a proper footing, which is not acceptable for a structural point load. We see the same pattern in late 1970s and 1980s backsplits in Markham and Mississauga, where the original truss drawings are long gone and nobody knows what the existing trusses were designed for.
What Plan Examiners Send Back on Addition Roofs
Most roof-related comments on addition permits fall into a small number of buckets. If your drawings handle these up front, the structural review tends to clear on the first pass.
- No snow drift shown or referenced, so the examiner can't confirm the trusses, header or beam were sized for the condition at the wall.
- A truss layout that shows a girder but no bearing detail, no post below it and no footing under the post.
- A header sized from span tables for floor loads only, with no roof or drift load included.
- Notes saying existing trusses will be cut, extended or overframed, with no manufacturer letter or engineer's design attached.
- Missing uplift and lateral ties where the new roof connects to the existing wall, particularly on ledger-supported shed roofs.
- Truss design drawings listed as a deferred submission with no note on when they'll arrive, which leaves the examiner unable to close the file.
Municipalities differ on timing. Some GTA building departments accept truss design drawings after permit issuance as long as they're in before the framing inspection, while others want the layout and girder reactions at application. Confirm the approach with your municipality before you submit, because it affects when you need to order trusses.
A Sequence That Keeps the Roof Out of the Revision Pile
Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.
The projects that move fastest follow roughly the same order, and the order matters more than any single decision.
Start by finding out what you have. Get into the attic and look for the manufacturer's stamp or tags on the trusses, check for any previous modifications, and pull whatever records exist from the original builder or the municipality's property file. A surprising number of tract homes in Vaughan and Oakville still have identifiable manufacturer tags, which makes it possible to request the original design drawings.
Next, settle the roof geometry with drift in mind. Moving the addition roof a few hundred millimetres away from the house with a separate beam, lowering the height difference, or changing the slope of the new roof can meaningfully reduce the drift your structure has to carry. That's a design conversation, and it's cheapest before anything is drawn in detail. At PermitsHub we work through the truss layout and the bearing points alongside the architectural drawings, so the girder positions line up with walls and footings rather than landing in the middle of a new kitchen.
Then get the truss designer or engineer the right inputs: municipality, roof geometry, height of the existing wall, slope of the upper roof and any mechanical units going on the new roof. The truss package comes back with girder reactions, and those reactions drive the posts and footings. Feed them into the foundation design immediately, especially if the addition already sits on a crawlspace or needs underpinning, because a concentrated load can change what the foundation work involves.
Finally, plan for the framing inspection. The inspector will want to see the stamped truss drawings on site, permanent bracing installed as shown, hangers fully fastened and posts bearing on proper footings. If the existing trusses were modified, the manufacturer's or engineer's detail needs to be there too, and some engineers will issue a field review letter after they've seen the work. When we coordinate submissions and examiner revisions for our clients, getting those documents lined up before the inspection booking is often the difference between passing on the first visit and waiting for a re-inspection.
The Signs Your Addition Roof Needs an Engineer, Not Just a Truss Supplier
A truss manufacturer can design new trusses and girders for the addition itself. An engineer becomes necessary when the existing structure is part of the equation. You're in engineer territory if existing trusses will be cut, removed or overframed, if a taller addition will drift snow onto the existing roof, if the opening in the rear wall is wide and carries roof plus floor, or if a point load lands on a foundation nobody has checked. Spotting these early keeps the structural scope honest and saves the uncomfortable conversation where the framing crew discovers the problem with the roof already open.
Do I Need a Permit?
What are you planning to build or renovate?
Ready to move forward? PermitsHub handles permit drawings, submission, and revisions - flat-rate, GTA-wide.