Structural
When Does a BCIN Designer Need a Structural Engineer for Your Permit?
A BCIN designer can sign most house permits in Ontario, but only while every beam and joist fits the Building Code's span tables. Once you remove a bearing wall, add a point load, underpin or retain soil, an engineer has to seal that part. Here's where the line actually falls, and how Toronto examiners expect the two sets to fit together.
Key Takeaways
- A BCIN designer can design and sign Part 9 house drawings, including framing, as long as every structural member fits the Ontario Building Code's prescriptive tables and standard details.
- Steel beams replacing bearing walls, concentrated point loads, underpinning, retaining walls over roughly a metre and second-storey additions on old foundations almost always need a PEO-licensed engineer's seal.
- Most Toronto renovation permits go in as a combined package: the designer's architectural sheets plus engineer-sealed structural sheets that must match exactly, or the examiner sends them back.
- Bringing the engineer in at design stage is far less disruptive than adding one after the first round of examiner comments, and their field reviews are often needed before inspections pass.
Designer Stamp, Engineer Seal
A BCIN-qualified designer can sign the full permit drawing set for most Part 9 houses in Ontario, framing included, as long as every structural member fits the Ontario Building Code's prescriptive span tables and standard details. Once the design steps outside those tables, a licensed professional engineer (P.Eng, licensed by Professional Engineers Ontario) has to design and seal that part. The usual triggers are steel beams carrying a removed load-bearing wall, concentrated point loads, underpinning, and retaining walls over about a metre. Most Toronto renovation permits end up as a combined package: the designer's architectural set plus engineer-sealed structural sheets.
What a BCIN Designer Is Actually Allowed to Sign
BCIN stands for Building Code Identification Number. Ontario's Ministry of Municipal Affairs and Housing issues it to designers who pass the Code exams in a given category. Designers who offer their services to the public also have to register under a firm BCIN and carry insurance. The House category covers detached, semi-detached and townhouse work under Part 9 of the Code, which applies to houses and small buildings up to three storeys and 600 square metres of building area. Within that scope, a qualified designer can produce and sign floor plans, sections, elevations, site plans and the framing design itself.
The important word is prescriptive. Part 9 is written so that ordinary wood-frame houses can be designed from tables and rules instead of calculations. It covers joist spans, rafter spans, lintel sizes, built-up wood beams, footing widths and stud spacing. If your loads and layout match the Code's assumptions, the table gives you the answer. A designer working inside those tables isn't guessing. They're applying the same tables the plan examiner uses to check the drawings.
Engineers and architects don't need a BCIN at all. Their licences from PEO and the Ontario Association of Architects already authorize them to design. That's why you'll see sealed structural sheets in a permit package with no BCIN box filled in on those pages.
Where the Span Tables Stop and Engineering Starts
One rule in Part 9 drives most of this decision. Structural members and connections that don't conform to the prescriptive requirements have to be designed under Part 4, the engineering design part of the Code. Part 4 means calculated loads, load combinations, member capacities and connection design. Some designers hold broader BCIN categories, but every GTA building department we submit to expects Part 4 structural work to arrive under an engineer's seal. We plan every project on that basis.
So the real question isn't whether you hire a designer or an engineer. It's whether each member fits a table. Here are a few common cases where the answer quietly flips:
- A floor joist that spans fine at 2x10 on 400 mm centres becomes an engineering problem once a bearing wall above lands mid-span instead of over a beam.
- The built-up wood beam tables assume uniform floor loads. Add a post from the second floor or a girder truss bearing on the beam and the table no longer applies.
- Part 9 has a limited table for steel beams supporting floors in houses. A steel beam replacing a main-floor bearing wall that also carries roof load, with new posts and footings, falls outside it.
- Engineered wood like LVL beams and I-joists is sized from manufacturer data, not Code tables. Suppliers often issue sizing sheets from their own software. Whether a municipality accepts that without a separate engineer depends on the city and how complicated the load path is.
The span tables assume loads arrive evenly and leave evenly. The minute something lands on a single point, you've left Part 9 and you need someone doing math.
Five Jobs That Almost Always Need an Engineer's Seal
Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.
After hundreds of GTA applications, these are the scopes where we bring in an engineer from day one rather than waiting for the examiner to ask.
Removing a load-bearing wall for an open plan
The beam that replaces the wall usually picks up floor joists from both sides. Sometimes it also carries a wall above, and sometimes roof load comes down through that wall. Someone has to size the flush steel or multi-ply LVL beam, the posts at each end, and the footings under those posts. Footings are the part homeowners forget. A post delivering a new concentrated load onto an old strip footing, or straight onto a basement slab, is exactly what examiners flag. In Toronto's east end, we've drawn dozens of these openings in narrow semis where the joists bear on a shared brick party wall. That shared wall adds another layer the engineer has to address.
Underpinning and lowering a basement
Underpinning means digging below the existing footings in short, sequenced sections. Toronto expects engineered drawings that show the pin sequence, the depths, the new footing sizes, and how the neighbour's foundation is protected where a wall is shared. On semis and row houses in Riverdale, Leslieville or the Junction, the party wall alone makes this an engineering job.
Retaining walls
The Code treats certain retaining walls as designated structures that need engineered design, mainly those over roughly a metre high next to public property or a walkway into the building. The trigger can depend on the wall's location, so confirm with your municipality. Walkouts, lowered side entrances for basement units and terraced backyards on ravine lots all tend to trigger it. On TRCA-regulated lots, the same engineering often feeds into the conservation authority's review.
Second-storey additions on existing houses
The new floor and roof framing may fit the tables, but the existing foundation and main-floor walls now carry more weight. Someone has to confirm that the old footings can take the added load. In pre-war houses those footings are often rubble stone or unreinforced concrete. That confirmation is an engineer's letter at minimum, and often a full design.
Heavy or unusual loads
Some loads go beyond what the tables were written for. Common ones are hot tubs on decks, rooftop terraces, green roofs, long cantilevers, wide new openings in exterior bearing walls and long-span garage door headers.
How a Combined Designer and Engineer Set Goes In
A typical Toronto renovation application has two parts. The designer supplies the A-sheets: site plan, floor plans, elevations, sections and construction notes. The engineer supplies the S-sheets or a sealed structural detail sheet. The designer's sheets carry their personal and firm BCIN. The engineer's sheets carry the PEO seal, signed and dated. Toronto Building also asks for a general review commitment, a form where the engineer agrees to review the structural work during construction.
The handoff between the two sets is where projects slow down. The designer's plans have to show the beam exactly where the engineer designed it, with matching sizes, post locations and footing call-outs. Say the A-sheet reads "steel beam by engineer" but the S-sheet shows a beam at a different elevation or with different post spacing. The examiner will send it back. At PermitsHub we produce the drawing set and coordinate the engineer's structural sheets in the same package, so both sets agree before submission instead of after the first round of comments.
What Plan Examiners and Inspectors Send Back
The most common structural comment we see isn't a flat "you need an engineer." It's a request showing that the drawings implied engineering without providing it. Typical wording looks like this:
- Provide engineered design for beam B1 and supporting posts, sealed by a professional engineer.
- Indicate footing size under new point load and provide design.
- Provide underpinning sequence and details sealed by a professional engineer.
- Structural members not conforming to Part 9 shall be designed in accordance with Part 4.
Each of those comments adds a resubmission cycle. Depending on the municipality's queue, that can add weeks to the permit. The comment also tends to arrive after you've lined up a contractor and a start date.
Inspectors pick up where examiners stop. On engineered work, the footing or framing inspection often won't pass until the inspector sees the engineer's field review letter confirming the beam, connections or underpinning went in as designed. Sometimes a contractor swaps the specified steel section for "something equivalent from the yard" without the engineer's sign-off. That creates a problem that can hold up drywall until the engineer comes back, checks it, and either accepts it in writing or asks for changes.
An engineer you can't get back to site is a permit you can't close. Ask about field reviews before you ask about the stamp.
Six Questions That Tell You Which One You Need
Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.
Before you hire anyone, run your project through these questions. They mirror what a plan examiner will be looking for.
- Are you removing or shortening any wall that supports a floor, a roof or another wall above?
- Will any new post, column or beam carry load from more than one level of the house?
- Are you digging below existing footings, lowering the basement floor or building a walkout?
- Is any wall holding back more than about a metre of soil?
- Are you adding a storey, a rooftop deck or a heavy fixed item like a hot tub?
- Is the house a semi or row house where structure is shared with a neighbour?
If every answer is no, a BCIN designer can very likely handle the whole set. That includes interior layout changes that don't touch bearing walls, basement finishing without lowering, decks within the span tables and most bathroom or kitchen work. Egress windows are a borderline case. Enlarging an opening in a poured or block foundation wall cuts into bearing structure, and some examiners will want an engineered lintel or opening detail. Check that one before you assume.
If any answer is yes, plan for both professionals from the start. The cost difference isn't really about the engineer's fee. It's about drawing the job twice. When the engineer joins after the first comments, the designer often has to redraw plans and sections around beam depths, post locations and footings that weren't known before. Bringing both in at design is meaningfully cheaper in time and revisions than retrofitting engineering into a set that's already been reviewed.
The reverse mistake also happens. Some homeowners hire an engineer for an entire house set when only one beam needed a seal, and they get drawings that are structurally thorough but thin on the zoning and architectural detail examiners check first. If you're unsure where your project falls, PermitsHub can do a free review of your scope and photos and tell you which elements a designer can carry and which ones will need a seal.
Do I Need a Permit?
What are you planning to build or renovate?
Ready to move forward? PermitsHub handles permit drawings, submission, and revisions - flat-rate, GTA-wide.