PermitsHubPermitsHub

Permits 101

Opening Up a Kitchen in a Scarborough Bungalow: When You Need a Permit

In most post-war Scarborough bungalows, the wall between the kitchen and living room is carrying the ceiling joists at mid-span. Taking it out means a building permit, a sized beam, and a clear path for the load all the way down to the footing. That path sometimes runs straight through a basement apartment. Here is how to tell what your wall is doing and what Toronto Building will ask for.

By PermitsHub Team9 min read

Key Takeaways

  • In most 1950s and 1960s Scarborough bungalows and side-splits, the kitchen wall is load bearing because it supports the ceiling joists at mid-span, so removing it requires a building permit from Toronto Building.
  • The permit drawings have to show the full load path: a beam sized by an engineer or qualified designer, posts at each end, and footings in the basement that can actually carry the concentrated load.
  • If there is a basement apartment below, the new posts and any beam work cannot break the fire separation between units, which often decides whether you choose a flush beam or a dropped beam.
  • Plumbing vents, return air ducts and wiring buried in the wall are what usually slow these jobs down, and moving a plumbing stack becomes part of the permit scope.

Opening the Scarborough Kitchen

Yes, in almost every case. If the wall between your kitchen and living room in a Scarborough bungalow is load bearing (and in post-war bungalows it usually is), removing it is a structural alteration under the Ontario Building Code and needs a building permit from Toronto Building before any demolition starts. If the wall is a true non-bearing partition with nothing buried inside it, you generally don't need a permit. But you have to prove that, not assume it.

Why the Kitchen Wall in a Scarborough Bungalow Is Usually Holding Something Up

Most of Scarborough's bungalow stock went up between the late 1940s and the late 1960s, in places like Wexford, Dorset Park, Bendale, Clairlea and Cliffcrest. The builders used the same basic recipe over and over. The roof is stick framed with rafters, and the ceiling joists span from the exterior wall to a central wall running the length of the house. That central wall is the one separating your kitchen from your living room, or the hallway from the bedrooms. It lands roughly at mid-span because 2x4 or 2x6 ceiling joists couldn't cross the full width of the house on their own.

Side-splits work a little differently, but the outcome is often the same. The kitchen sits on the main level, and the wall beside it may be carrying the floor of the bedroom level above, not just an attic. That is a heavier load. Expect a deeper beam and bigger posts.

There are exceptions. Some later 1960s builds used engineered roof trusses that span wall to wall. In those houses the interior walls carry nothing but drywall. You won't know which one you have until someone looks in the attic.

Quick checks you can do before calling anyone

  • Go into the attic and look at what sits on top of the wall. Ceiling joists overlapping or butting together over it is a strong sign it's bearing. Triangulated trusses with metal gusset plates suggest it may not be.
  • Go into the basement and look directly under the wall. A steel beam or built-up wood beam running parallel to it, with posts, usually means the wall above is part of the main load line.
  • Check which way the wall runs. A wall running the long direction of the house, parallel to the ridge, is the usual suspect in a bungalow.
  • Look for a heating register, a return air grille or a plumbing vent through the roof directly above. These don't tell you about structure, but they tell you the wall isn't empty.

None of these checks replace a proper assessment. They just help you walk into the conversation knowing whether you're likely looking at a permit job.

Following the Load Down: Beam, Posts and Footings

Homeowners picture this job as swapping a wall for a beam. Plan examiners picture it as a load path. Everything the wall used to carry along its whole length now concentrates at two or three points where the beam ends sit on posts. Those point loads have to travel down through the floor framing, into the basement, and onto a footing that can take them. If any link in that chain is weak, the drawings come back.

The beam itself is usually LVL (laminated veneer lumber) or steel, sized for the span, the tributary width of ceiling or floor it supports, and the snow load on the roof above. Someone qualified has to size it: a professional engineer, or a designer holding the right BCIN qualification working within what the code allows them to design. Toronto Building wants to see the beam size, the bearing length at each end, the post size and the connection details on the drawings.

Then comes the part people skip. Where the new post lands on the main floor, there has to be solid blocking or framing beneath it, and that load has to reach the basement. In a lot of Scarborough bungalows, the existing basement posts sit on modest concrete pads poured in the 1950s. Sometimes they sit on nothing more than the basement slab. If your new post load lands between two existing posts, or on a slab with no footing under it, you'll need a new footing pad. That means cutting the basement floor, excavating, and getting a footing inspection before the concrete goes in.

The beam is the easy part. The question that stalls the permit is always where that post load ends up in the basement, and whether anything down there was ever built to carry it.

Flush beam or dropped beam

A dropped beam hangs below the ceiling. It's simpler and cheaper to build, and you can usually install it from below with temporary shoring walls on both sides. A flush beam sits up in the ceiling plane, so you get a clean, flat ceiling. To do it, the existing joists get cut and hung off the beam with joist hangers. That means more work in the attic, more temporary support, and a more detailed drawing. Most people opening a kitchen want the flush look, and it's very doable in a bungalow, but it adds to the scope.

When There's a Basement Apartment Underneath

Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.

Scarborough has a lot of bungalows with basement units, some legal and registered, many not. If yours has one, opening the kitchen upstairs gets more complicated in two ways.

First, the new posts and footings may need to go through the apartment. A post that used to be hidden in a wall upstairs might now need to come down in the middle of a tenant's living room, unless the engineer can route the load to an existing line. Work inside an occupied unit also means coordinating access and notice with the tenant.

Second, the ceiling of the basement unit is usually acting as the fire separation between the two dwelling units. Cutting into it to add blocking, to reach a post base, or to reroute ductwork breaks that separation. The drawings have to show how it gets restored, typically with the right type of drywall and sealed penetrations, so it still meets the fire rating the code requires for that house. Inspectors check this. If the basement suite was never permitted, the examiner may ask questions you weren't planning to answer yet. Know that going in. Sometimes the sensible move is to legalise the suite and open the kitchen under the same application.

What's Hiding Inside a 1950s Kitchen Wall

In our experience on Scarborough bungalows, the structure is rarely what blows up the schedule. The services are. The kitchen side of the central wall is where builders ran the plumbing vent stack for the sink, the cold air return for the furnace, and a surprising amount of knob and tube or early wiring.

  • Plumbing vent stack: if it's in the wall you're removing, it has to be relocated. That plumbing work becomes part of your building permit scope and gets its own inspection.
  • Return air duct: these often run up the wall cavity from a floor grille. Losing it can starve the furnace of return air, so the HVAC layout needs rethinking, not just capping.
  • Electrical: switches, receptacles and runs through the wall need rerouting. That's handled through the Electrical Safety Authority, separate from the building permit, by a licensed electrical contractor.
  • Plaster and attic insulation: original plaster and some loose-fill attic insulation in homes of this age can contain asbestos. Have suspect materials tested before anyone cuts or opens the ceiling for a flush beam.

What the Scarborough District Office Actually Reviews

Permit applications for Scarborough addresses are handled by Toronto Building's Scarborough district, based at the Scarborough Civic Centre, though most submissions now go in electronically. For an interior wall removal, the review is mostly a Building Code review. Interior alterations don't change setbacks, height or coverage, so zoning is rarely an issue, and you won't need the Committee of Adjustment.

A complete application for this kind of job usually includes:

  • An existing and proposed floor plan of the main floor showing the wall to be removed.
  • A basement plan showing where the new posts land and any new footings.
  • A section or detail through the beam showing joist connections, bearing and post sizing.
  • Beam and footing design, with engineer's calculations or manufacturer sizing for LVL where required.
  • Plumbing and HVAC changes if the stack or return air is moving.
  • Fire separation details if there's a second unit in the house.

The most common reasons examiners send these back are a missing basement plan, a post that lands on nothing in particular, no detail for how the joists connect to a flush beam, and no mention of the fire separation in a house that clearly has two units. Get those four right and these permits tend to move through fairly quickly. The Building Code sets a short review window for houses. Revision rounds are where the time goes, so confirm current timelines with the city. PermitsHub prepares the structural drawings and basement load path details for these jobs and handles the examiner's comments if any come back.

On Site: Shoring, Inspections and Closing the Ceiling

Have a project in mind? Get an honest, no-pressure permit review from PermitsHub.

Once the permit is issued, the contractor builds temporary shoring walls on both sides of the old wall to hold the ceiling joists, sometimes at the basement level too. Then the old wall comes out, posts and footings go in, and the beam is set. If a new footing is required, the inspector checks the excavation before the concrete pour. After the beam, posts and connections are in place, but before any drywall goes up, you call for a framing or structural inspection. Plumbing gets its own inspection if the stack moved, and ESA inspects the electrical.

The mistake we see most is closing the ceiling or boxing in a post before the inspection. The inspector can then ask for drywall to come off. Build a day or two of buffer into the schedule for booking. PermitsHub can coordinate the inspection requests so the trades aren't sitting idle.

What Happens If You Take the Wall Out Without a Permit

Usually nothing happens right away, and that's the trap. The issues show up later. Ceilings sag and crack over a beam that was undersized or sat on a post with no footing. A buyer's home inspector spots an open-concept main floor in a 1955 bungalow with no permit on file and asks about it. An insurer asks questions after a claim. Toronto Building can also issue an order if the work is reported, often by a neighbour who watched the dumpster fill up. Fixing that after the fact means opening finished ceilings so an inspector can see the beam and connections, and producing drawings for work that's already built. It is meaningfully more disruptive than getting the permit at the start.

If you already know the wall is coming down, have the attic and basement looked at first, get the load path drawn properly, and pull the permit. In a Scarborough bungalow, that is how an open kitchen stays flat and quiet for the next fifty years.

Do I Need a Permit?

1
›
2
›
3
›
4

What are you planning to build or renovate?

Ready to move forward? PermitsHub handles permit drawings, submission, and revisions - flat-rate, GTA-wide.

Related Reading

More in this category

Permits 101

FAQ

Related questions

Get started

Tell us about your project.

Free, no-pressure quote within one business day.

● Flat-rate quotes - no surprise fees

● Revisions included until approval

● Most enquiries responded to same day

Free Home Permit QuoteNo commitment · 30 sec
1
2
3

What are you building?

SCROLL TO SEE ALL 20 PERMIT TYPES

Prefer to call? 647-961-4070
CALL NOWFree Home Permit Quote30 SECONDS - NO COMMITMENT